TORQUETRAK TPM2TORQUE AND POWER MONITORING SYSTEM

Continuous Torque and Power Data from Rotating Shaft

The TorqueTrak Torque and Power Monitoring System (TPM2 series) is a rugged precision instrument designed to measure torque and/or power on rotating shafts in real time. The TPM2 uses RS422 full duplex, point – to – point serial interface communication. The TPM2 is custom designed to fit on shafting up to 40 inches (1016 mm) in diameter. Machine disassembly is not required.

  • Software for setup and configuration
  • Digital RS422 output
  • Splash resistant control box
  • Selectable input ranges
  • High RPM / centrifugal g-force rating

特徴

  • Easy Installation
    Rotating Collar and Stationary Ring are split and bolt together around the shaft. No Machine assembly or Shaft modification is required.
  • Robust Construction
    Sturdy hardware and electronics, built for demanding environments.
  • Reliable Operation
    Inductive power and data transfer with generous clearance between stationary and rotating parts. No wear surfaces.
  • System Status Indicators
    Confirm proper operation at a glance. Expedites troubleshooting.
  • Easy-on Collar
    Rotating Collar is designed to accommodate small variations in shaft diameter and clamps to the shaft using standard tools.
  • Communications Made Easy
    High-speed bi-directional communications link interfaces with PC or PLC. User-selectable sample rate up to 4800 samples/second.
  • Product Support
    Backed by BEI’s proven outstanding customer service, before and after the sale.

TORQUETRAK TPM2 Specification

寸法インチ(mm)

カラー外寸直径 A シャフト外寸(min.) シャフト外寸(max.) 最大回転数(RPM)
5.0(127) 0.8(20) 1.5(38) 9100
5.5(140) 1.0(25) 2.0(51) 8500
7.5(191) 2.0(51) 4.0(102) 6900
9.5(241) 4.0(102) 6.0(152) 5900
11.5(292) 6.0(152) 8.0(203) 4300
13.5(343) 8.0(203) 10.0(254) 3800
15.5(394) 10.0(254) 12.0(305) 3400
17.5(445) 12.0(305) 14.0(356) 3100
19.5(495) 14.0(356) 16.0(406) 2800
21.5(546) 16.0(406) 18.0(457) 2300
23.5(597) 18.0(457) 20.0(508) 2200
25.5(648) 20.0(508) 22.0(559) 2100
27.5(699) 22.0(559) 24.0(610) 1900
31.5(800) 24.0(610) 28.0(711) 1500
35.5(902) 28.0(711) 32.0(813) 1400
39.5(1003) 32.0(813) 36.0(914) 1300
43.5(1105) 36.0(914) 40.0(1016) 1200

シャフト径が1016mm以上の場合は、最寄りの販売代理店へご連絡いただくか、Binsfeld.comからご連絡ください。

TorqueTrak TPM2 Specification

POWER SUPPLY INPUT
10 – 30 VDC @ 10 W (nom), 15 W (max)
TORQUE SENSOR INPUT
Strain gage bridge, 350 ohms (std), 120 ohms (min)
Input Range
user-selectable from 0.025 to 32 mV/V
Shunt Calibration
2 user-selectable: 1 mV/V and 0.2 mV/V (350 ohm bridge)
TORQUE SENSOR RESOLUTION
15 bit (32,768 points)
TORQUE SIGNAL ACCURACY
Zero error:±0.1% FS (max), Scale error: ±0.2% (max)
TORQUE SIGNAL BANDWIDTH
10 user-selectable settings from 3 to 1000 Hz
Measured once per revolution
15 bit (32,768 points), auto-ranging
COMMUNICATION INTERFACE
RS(EIA)-442 full duplex, up to 1000 ft (300 m) run
Baud Rate
Auto-detectable from 1200 to 460,800 bps
Sample Rate
10 user-selectable settings from 9.375 to 4800 samples/sec
OPERATING ENVIRONMENT
-40° to +70° non-condensing

Specifications are subject to change without notice.